Kablar och adaptrar/Ström/Strömkontaktar

SmartLife Smart Plug

Wi-Fi | Strömmätare | 2500 W | Jordad kontakt / Typ F (CEE 7/7) | -10 - 40 °C | Android™ / IOS | Vit | 1 st.

Egenskaper

Tillverkarens artikelnummer: WIFIP110FWT
Streckkod: 5412810269945
• Kan användas som fristående produkt eller kan enkelt anslutas till andra Nedis SmartLife-produkter
• Möjliggör fjärrstyrd och automatiserad styrning - för att schemalägga och länka apparater
• Stöd för röststyrning - tillsammans med Amazon Alexa eller Google Home
• Tunn design - för att säkerställa att angränsande uttag inte blockeras
Styr många elektriska apparater på distans genom att enkelt ansluta dem till den här trådlösa smarta kontakten och anslut dem till din smartphone eller surfplatta via Wi-Fi-routern. Med den praktiska strömmonitorn kan du snabbt se exakt hur mycket ström produkten använder just nu, eller hur mycket ström den har använt.

Enkel att installera
Du behöver inte vara en teknisk begåvning eller elektriker för att styra och automatisera dina anslutna apparater och enheter. Allt du behöver är en smart kontakt och din Wi-Fi-router. Vår intuitiva app ger dig möjlighet att slå på eller av apparater på distans och automatiskt. Den kan även fungera tillsammans med röststyrningssystem som Amazon Alexa eller Google Home.

Supertunn - inga fler blockerade uttag
Dessa supertunna apparater har utformats för att undvika problemet med att smarta kontakter blockerar angränsande uttag - våra kontakter är både smarta och tunna för din bekvämlighet.

Schemalägg och para ihop
Ställ in tidsscheman för när kontakten ska slå på apparater eller koppla dem med andra för att skapa rätt stämning som kan aktiveras med ett enda kommando eller en enda knapptryckning.

Övervaka strömförbrukning
Identifiera apparater som använder för mycket ström snabbt för att se till att du lever i ett smart och energisnålt hem.

Om Nedis SmartLife
Upptäck ett stort och ständigt växande sortiment av produkter - såsom lampor, brytare, uttag, sensorer och kameror - som alla kan styras med en lättanvänd och intuitiv app. Med röststyrningsfunktioner som stöds av Amazon Alexa och Google Home och utan behov av något annat än ditt befintliga Wi-Fi-nätverk är detta ett anslutet, smart hem på ett enkelt sätt.
Oavsett om du letar efter en enda smart lampa eller ett uttag, eller om du vill automatisera hela huset, kan du upptäcka hur lättillgänglig smart teknik är i dag.

Förpackning

Paketet innehåller

Smart kontakt
Snabbstartsguide

Storlek på förpackning Presentask med eurolock

Bredd Höjd Längd
105 mm 125 mm 63 mm

Förpackningsstorlek

Antal/kartong Bredd Höjd Längd Vikt
1 65 mm 150 mm 110 mm 107 g
50 345 mm 285 mm 560 mm 6000 g

Produktspecifikationer

Bredd 45 mm
Höjd 70 mm
Djup 45 mm
Vikt 57 g
Färg Vit
Material Plast
Kompatibel med Nedis® SmartLife
Maximal antennförstärkning 1.5 dBi
Maximal sändningseffekt 14 dBm
Strömmätare Ja
Enhetens ströminmatningsanslutning Hybrid (CEE 7/7)
Uteffekt 2500 W
Ingångsström 10 A
App tillgänglig för Android™
IOS
Sänd frekvensområdet 2412 - 2472 MHz
Nätkontakt Typ F (CEE 7/7)
Förpackningstyp Gift Box with Euro Lock
Trådlös teknologi som stöds Wi-Fi
Utström 10 A
Antal varor i paketet 1 st.
Drifttemperaturens omfång -10 - 40 °C
Enhetens utgångsanslutning Jordad kontakt / Typ F (CEE 7/7)
Typ av jordning Jordad kontakt
Inspänning 230 V AC

Support

Vanliga frågor

Vi har hittat följande frågor åt dig på engelska

Go to the settings menu of the plug > remove device and data
Then go to Profile > settings > clear cache
Now reset the plug and add it back to the app

Please try the AP mode.

Make sure that you use a 2.4Ghz wifi network.

Reset the plug so it blinks slow.

If it blinks fast, reset it again and it will blink slowly



In the app:

+ > [your device] > tap on EZ mode and select AP mode > confirm it was reset > fill in the info of your wifi network > follow the steps in the app.



Hold your phone very close to the plug during the installation

This method uses a direct connection to the device to send the info of your wifi to it.

Holding it close optimises this connection

Nedis Smart plugs are designed and tested to be used as power supply for consumer products. Since there are no applicable standards developed yet Nedis Smart plugs are not designed and not tested to be used as a feed-in component into a power grid and/or to be used in combination with solar (balcony) panels.

Nedis Smart plugs are designed and tested to be used as power supply for consumer products. Since there are no applicable standards developed yet Nedis Smart plugs are not designed and not tested to be used as a feed-in component into a power grid and/or to be used in combination with solar (balcony) panels.

To control your Nedis SmartLife products with Google Assistant, you need to assign your Smart Life products in a room also in Google home.

1. Start the Google home app.
2. choose Settings
3. choose More Settings
4. Go to the tab off your home.
5. If a device is not assigned to room, tab on the device name and assign it to a room.

Now, you can control your devices by Google home products.


Add the "Smart Life" service to Google Home (no Nedis in the name).

Go in Google Home to Assistent -> Home Control and choose here "Smart Life" as service.

Use the Login details of the "Nedis Smartlife" app.
Compatible Nedis SmartLife products will then be added to Google Home.

An automation can be used to make a certain "event"(condition), trigger another action (Task)
A condition can be anything from motion detection, to a certain time, a certain temperature, sunrise.
Then you can make this condition turn on lights, turn on smart plugs, make a siren sound or a combination of multiple tasks.

You can add maximum 20 members.

Yes you can.
Each person needs a unique account on their mobile device.
To add them as "family members" follow these steps:
In the main screen of the app tap on the name of your home (top left)
Tap on Home management
Tap on the name of your home again.
Tap on "add family members" and fill in the account details of the person you want to add.
It will give them access to all the devices in your home as a normal member or admin (you can select this)

If you only want to share a single device in a home, go to the settings menu of the device and select "share device" -> add member.

This is probably a Wifi problem, this can be for various reasons.
1.) Wifi signal is unstable.
2.) Wifi signal is too weak.
3.) Using an access point with the same SSID and password that do not support the IEEE 802.11R standards.

Problem 1 can often be solved by restarting the router.
Problem 2 can be checked with an app Wifi analyzer with this the signal can be viewed and corrected to a better position.
Problem 3 can be checked as the access points are turned off, the Wifi signal is still good and the connection remains if the access points are a problem, a Mesh solution can then be used.
Please make sure that they support IEEE 802.11R standard.