Bande LED SmartLife
Wi-Fi | Blanc Chaud / Blanc Froid / RGB | SMD | 5.00 m | IP44 | 2700 - 6500 K | 960 lm | Android™ / IOS
Caractéristiques
• Les couleurs rouge, vert et bleu sont disponibles ou vous pouvez choisir un blanc chaud ou froid, pour correspondre parfaitement à votre humeur
• La bande peut être raccourcie ou allongée, pour des possibilités infinies
• Adhésif double face (3M) déjà en place pour une installation facile
• Fonctionne comme un éclairage intelligent autonome. Peut être couplé à d'autres produits SmartLife pour créer une maison intelligente complète
Cette bande de LED combinant des LED RGB et des LED blanches chaudes et froides, vous pouvez non seulement définir une couleur préférée, mais aussi l'utiliser pour un éclairage indirect blanc chaud à froid
Sa longueur de 5 mètres peut être raccourcie ou étendue avec des bandes LED similaires pour des possibilités infinies
L'adhésif double face (3M) est déjà en place, pour une installation facile sur n'importe quelle surface propre et plane.
Emballage
Contenu de l'emballage
Bande de LED RGBW (5 m)
Contrôleur Wi-Fi
Alimentation
Guide de démarrage rapide
Dimensions emballage retail Boîte cadeau avec eurolock
Largeur | Hauteur | Longueur |
---|---|---|
50 mm | 190 mm | 185 mm |
Dimensions logistiques
Conditionné par | Largeur | Hauteur | Longueur | Poids |
---|---|---|---|---|
1 | 182 mm | 50 mm | 210 mm | 420 g |
8 | 195 mm | 245 mm | 420 mm | 3720 g |
32 | 410 mm | 440 mm | 510 mm | 16000 g |
Spécifications du produit
Largeur |
151 mm |
Hauteur |
8 mm |
Profondeur |
5000 mm |
Poids |
310 g |
Tension d'entrée |
220 - 240 V AC 50/60 Hz |
Gain d'antenne d'émission maximal |
2.5 dBi |
Compatible avec |
Nedis® SmartLife |
Longueur du câble de l'adaptateur secteur |
1.50 m |
Puissance d'émission maximale |
16 dBm |
Indice de rendu des couleurs (Ra) |
80 |
Couleur de lumière |
Blanc Froid Blanc Chaud RGB |
Application disponible pour |
Android™ IOS |
Classement IP |
IP44 |
Consommation électrique maximale |
15 W |
Fiche d'alimentation |
Euro (CEE 7/16) |
Variable |
Oui |
Durée de vie nominale de la lampe |
20000 h |
Technologie sans fil sountenu |
Wi-Fi |
Découpable |
Oui |
Consommation d'énergie pour 1000 heures |
15 kWh |
Matériau |
Silicone |
Support de montage |
Monté sur la surface |
Bande lumineuse extensible |
Oui |
Plage de fréquences de transmission |
2412 - 2484 MHz |
Nombre de produits dans l'emballage |
1 pièces |
Connexion (s) d'entrée d'alimentation de l'appareil |
DC |
Température Couleur |
2700 - 6500 K |
Classe énergétique |
F |
Flux lumineux nominal |
960 lm |
Couleur |
Multicolore |
Longueur de la corde |
5.00 m |
Type de LED |
SMD |
Module LED |
SMD 5050 |
Nombre de leds par mètre |
90 pièces |
Assistance
Questions fréquemment posées
Nous avons trouvé les questions suivantes pour vous en anglais
Can the strip light up in multiple colours at the same time?
No, the LED's are not individually addressable.
My LED strip does not want to install with the EZ mode installation.
Please try the AP mode.
Make sure that you use a 2.4Ghz wifi network.
Reset the controller so the LED strip blinks slow. (press and hold the button on the controller)
If it blinks fast, reset it again and it will blink slowly
In the app:
+ > [your device] > tap on EZ mode and select AP mode > confirm it was reset > fill in the info of your wifi network > follow the steps in the app.
Hold your phone very close to the plug during the installation
This method uses a direct connection to the device to send the info of your wifi to it.
Holding it close optimises this connection
Can I just take the adhesive strip off?
Ensure that you only take off the plastic protection and not the entire adhesive strip.
If you remove the whole strip, you will not be able to stick it to anything.
Can I extend the strip?
Yes, you can purchase another set and plug the second strip in the first one.
If you extend it to 10m (5m extra) then you might see some loss in brightness at the end of the second strip.
We recommend you install multiple complete sets and group them in the app.
Now you can control all of the strips as if they are a single strip without any loss in brightness.
Can I give other people access to my Smartlife devices too?
Yes you can.
Each person needs a unique account on their mobile device.
To add them as "family members" follow these steps:
In the main screen of the app tap on the name of your home (top left)
Tap on Home management
Tap on the name of your home again.
Tap on "add family members" and fill in the account details of the person you want to add.
It will give them access to all the devices in your home as a normal member or admin (you can select this)
If you only want to share a single device in a home, go to the settings menu of the device and select "share device" -> add member.
My Smartlife products lose the Wifi connection every time.
This is probably a Wifi problem, this can be for various reasons.
1.) Wifi signal is unstable.
2.) Wifi signal is too weak.
3.) Using an access point with the same SSID and password that do not support the IEEE 802.11R standards.
Problem 1 can often be solved by restarting the router.
Problem 2 can be checked with an app Wifi analyzer with this the signal can be viewed and corrected to a better position.
Problem 3 can be checked as the access points are turned off, the Wifi signal is still good and the connection remains if the access points are a problem, a Mesh solution can then be used.
Please make sure that they support IEEE 802.11R standard.